博客
关于我
强烈建议你试试无所不能的chatGPT，快点击我
Rhel6-keepalived+lvs配置文档
阅读量：6973 次
发布时间：2019-06-27

本文共 8400 字，大约阅读时间需要 28 分钟。

系统环境: rhel6 x86_64 iptables and selinux disabled

主机: 192.168.122.119 server19.example.com

192.168.122.25 server25.example.com

192.168.122.163 server63.example.com

192.168.122.193 server93.example.com

所需的包:keepalived-1.2.7.tar.gz

Realserver1 192.168.122.163:apache

Realserver2 192.168.122.193:apache

Load Balance 192.168.122.119:keepalived

Load Balance 192.168.122.25:keepalived

Virtual IP 192.168.122.178

以下步骤在server19和server25上实施:

[root@server19 ~]# yum install kernel-devel make gcc -y

[root@server19 ~]# yum install openssl-devel popt-devel -y

[root@server19 ~]# yum install libnl-devel -y

以下步骤在server19或server25上实施:

[root@server19 kernel]# tar zxf keepalived-1.2.7.tar.gz

[root@server19 kernel]# cd keepalived-1.2.7

[root@server19 keepalived-1.2.7]# ./configure –prefix=/usr/local/keepalived

[root@server19 keepalived-1.2.7]# make && make install

[root@server19 keepalived-1.2.7]# scp -r /usr/local/keepalived/ :/usr/local/

以下步骤在server19和server25上实施:

[root@server19 keepalived-1.2.7]# ln -s /usr/local/keepalived/etc/keepalived/ /etc/

[root@server19 keepalived-1.2.7]# ln -s /usr/local/keepalived/etc/sysconfig/keepalived /etc/sysconfig/

[root@server19 keepalived-1.2.7]# ln -s /usr/local/keepalived/etc/rc.d/init.d/keepalived /etc/init.d/

[root@server19 keepalived-1.2.7]# ln -s /usr/local/keepalived/sbin/keepalived /sbin/

注：系统镜像的负载均衡套件中也集成了keepalived,也可以直接使用yum install keepalived -y进行安装。但需先配置yum源：

[LoadBalancer]

name=Instructor Server Repository

baseurl=ftp://192.168.122.1/pub/yum/LoadBalancer

gpgcheck=1

gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release

enabled=1

以下步骤在server19实施:

[root@server19 ~]# vim /etc/keepalived/keepalived.conf

global_defs {

notification_email {

root@localhost 错误发送至此邮箱

}

notification_email_from keepalived@server19.example.com 发信人

smtp_server 127.0.0.1

smtp_connect_timeout 30

router_id LVS_DEVEL

}

vrrp_instance VI_1 {

state MASTER 角色:(1)MASTER (2)BACKUP

interface eth0

virtual_router_id 51 (主备的配置需要一致)

priority 100 优先级（数字越大，优先级越高）

advert_int 1

authentication {

auth_type PASS 认证类型

auth_pass 1111 认证密码

}

virtual_ipaddress {

192.168.122.178 虚拟IP，可设置多个

}

}

virtual_server 192.168.122.178 80 {

delay_loop 6

lb_algo rr

lb_kind DR

# nat_mask 255.255.255.0

# persistence_timeout 50

protocol TCP

real_server 192.168.122.163 80 {

weight 1

TCP_CHECK { (注:TCP_CHECK和大括号之间要有空格)

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

real_server 192.168.122.193 80 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

}

 

以下步骤在server25实施:

[root@server25 ~]# vim /etc/keepalived/keepalived.conf

global_defs {

notification_email {

root@localhost 错误发送至此邮箱

}

notification_email_from keepalived@server25.example.com 发信人

smtp_server 127.0.0.1

smtp_connect_timeout 30

router_id LVS_DEVEL

}

vrrp_instance VI_1 {

state BACKUP 角色:(1)MASTER (2)BACKUP

interface eth0

virtual_router_id 51 (主备的配置需要一致)

priority 50 优先级（数字越大，优先级越高）

advert_int 1

authentication {

auth_type PASS 认证类型

auth_pass 1111 认证密码

}

virtual_ipaddress {

192.168.122.178 虚拟IP，可设置多个

}

}

virtual_server 192.168.122.178 80 {

delay_loop 6

lb_algo rr

lb_kind DR

# nat_mask 255.255.255.0

# persistence_timeout 50

protocol TCP

real_server 192.168.122.163 80 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

real_server 192.168.122.193 80 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

}

以下步骤在server63上实施:

[root@server63 ~]# yum install arptables_jf httpd -y

[root@server63 ~]# arptables -A IN -d 192.168.122.178 -j DROP

[root@server63 ~]# arptables -A OUT -s 192.168.122.178 -j mangle --mangle-ip-s 192.168.122.163

[root@server63 ~]# /etc/init.d/arptables_jf save

[root@server63 ~]# ifconfig eth0:0 192.168.122.178 netmask 255.255.255.255 up

或

[root@server63 ~]# ip addr add 192.168.122.178 dev eth0

注：可用ip addr show查看

[root@server63 ~]# echo `hostname` > /var/www/html/index.html

[root@server63 ~]# /etc/init.d/httpd start

 

以下步骤在server93上实施:

[root@server93 ~]# yum install arptables_jf httpd -y

[root@server93 ~]# arptables -A IN -d 192.168.122.178 -j DROP

[root@server93 ~]# arptables -A OUT -s 192.168.122.178 -j mangle --mangle-ip-s 192.168.122.193

[root@server93 ~]# /etc/init.d/arptables_jf save

 

[root@server93 ~]# ifconfig eth0:0 192.168.122.178 netmask 255.255.255.255 up

或

[root@server93 ~]# ip addr add 192.168.122.178 dev eth0

注：可用ip addr show查看

[root@server93 ~]# echo `hostname` > /var/www/html/index.html

[root@server93 ~]# /etc/init.d/httpd start

以下步骤在server19和server25上实施:

[root@server19 ~]# /etc/init.d/keepalived start

测试:

执行ip addr show可查看虚拟IP,执行ipvsadm -l查看规则是否加载，访问192.168.122.178反复刷新网页,每次出现的页面都不同说明配置成功. 当主备挂掉后可由另一台接管,当两台都正常时由Master充当调度器.

#配置多个服务（apache+ftp）

以下步骤在server19实施:

[root@server19 ~]# vim /etc/keepalived/keepalived.conf

global_defs {

notification_email {

root@localhost

}

notification_email_from keepalived@server19.example.com

smtp_server 127.0.0.1

smtp_connect_timeout 30

router_id LVS_DEVEL

}

vrrp_instance VI_1 {

state MASTER

interface eth0

virtual_router_id 51 (主备的配置需要一致)

priority 100

advert_int 1

authentication {

auth_type PASS

auth_pass 1111

}

virtual_ipaddress {

192.168.122.178 虚拟IP，可设置多个

}

}

virtual_server 192.168.122.178 80 {

delay_loop 6

lb_algo rr

lb_kind DR

# nat_mask 255.255.255.0

# persistence_timeout 50

protocol TCP

real_server 192.168.122.163 80 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

real_server 192.168.122.193 80 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

}

virtual_server 192.168.122.178 21 {

delay_loop 6

lb_algo rr

lb_kind DR

# nat_mask 255.255.255.0

persistence_timeout 50 持续连接时间为50s

protocol TCP

real_server 192.168.122.163 21 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

real_server 192.168.122.193 21 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

}

 

以下步骤在server25实施:

[root@server25 ~]# vim /etc/keepalived/keepalived.conf

global_defs {

notification_email {

root@localhost

}

notification_email_from keepalived@server25.example.com

smtp_server 127.0.0.1

smtp_connect_timeout 30

router_id LVS_DEVEL

}

vrrp_instance VI_1 {

state BACKUP

interface eth0

virtual_router_id 51 (主备的配置需要一致)

priority 50

advert_int 1

authentication {

auth_type PASS

auth_pass 1111

}

virtual_ipaddress {

192.168.122.178 虚拟IP，可设置多个

}

}

virtual_server 192.168.122.178 80 {

delay_loop 6

lb_algo rr

lb_kind DR

# nat_mask 255.255.255.0

# persistence_timeout 50

protocol TCP

real_server 192.168.122.163 80 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

real_server 192.168.122.193 80 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

}

virtual_server 192.168.122.178 21 {

delay_loop 6

lb_algo rr

lb_kind DR

# nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.122.163 21 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

real_server 192.168.122.193 21 {

weight 1

TCP_CHECK {

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

}

}

以下步骤在server63上实施:

[root@server63 ~]# yum install arptables_jf httpd vsftpd -y

[root@server63 ~]# arptables -A IN -d 192.168.122.178 -j DROP

[root@server63 ~]# arptables -A OUT -s 192.168.122.178 -j mangle --mangle-ip-s 192.168.122.163

[root@server63 ~]# /etc/init.d/arptables_jf save

[root@server63 ~]# ifconfig eth0:0 192.168.122.178 netmask 255.255.255.255 up

或

[root@server63 ~]# ip addr add 192.168.122.178 dev eth0

注：可用ip addr show查看

[root@server63 ~]# echo `hostname` > /var/www/html/index.html

[root@server63 ~]# /etc/init.d/httpd start

[root@server63 ~]# touch /var/ftp/server63

[root@server63 ~]# /etc/init.d/vsftpd start

 

以下步骤在server93上实施:

[root@server93 ~]# yum install arptables_jf httpd vsftpd -y

[root@server93 ~]# arptables -A IN -d 192.168.122.178 -j DROP

[root@server93 ~]# arptables -A OUT -s 192.168.122.178 -j mangle --mangle-ip-s 192.168.122.193

[root@server93 ~]# /etc/init.d/arptables_jf save

[root@server93 ~]# ifconfig eth0:0 192.168.122.178 netmask 255.255.255.255 up

或

[root@server93 ~]# ip addr add 192.168.122.178 dev eth0

注：可用ip addr show查看

[root@server93 ~]# echo `hostname` > /var/www/html/index.html

[root@server93 ~]# /etc/init.d/httpd start

[root@server93 ~]# touch /var/ftp/server93

[root@server93 ~]# /etc/init.d/vsftpd start

 

以下步骤在server19和server25上实施:

[root@server19 ~]# /etc/init.d/keepalived start

转载于:https://www.cnblogs.com/xautlmx/p/4002309.html

你可能感兴趣的文章
linux getch()实现
查看>>
[宽度优先搜索] FZU-2150 Fire Game
查看>>
group by
查看>>
简单投票系统学到的一些东西
查看>>
简明 Vim 练级攻略(转载)
查看>>
ubuntu12.04下virtualbox访问usb
查看>>
android打电话，接电话，挂电话过程
查看>>
【LeanEAP.NET】精益企业应用平台实战----表格批量编辑与Undo/Redo功能实现
查看>>
从Excel中读取数据(python-xlrd)
查看>>
iframe显示高度自适应 兼容多浏览器
查看>>
Struts2 技术全总结 （正在更新）
查看>>
站在产品经理的角度看问题
查看>>
SVN的具体使用方法介绍（安装以及操作）
查看>>
P1064 金明的预算方案
查看>>
Zabbix监控平台3.2.4（一）搭建部署与概述
查看>>
系统升级与优化
查看>>
网络编程之urllib
查看>>
Simple Python Dictionary :)
查看>>
c语言程序设计第六次作业--循环结构（二）
查看>>
【转】WebView的JavaScript与本地代码三种交互方式
查看>>
喝酒易醉，品茶养心，人生如梦，品茶悟道，何以解忧？唯有杜康！-- 愿君每日到此一游！
当前时间: 2025-02-04 21:52:51   当前IP: 18.118.200.142   联系邮箱:javaeecc@qq.com     Copyright © 2020 - 2022 baihongyu.com 京ICP备2021015314号-2
强烈建议你试试无所不能的CHAT-GPT，快点击我
强烈建议你试试无所不能的CHAT-GPT，快点击我